PHP 8.3.4 Released!

else

(PHP 4, PHP 5, PHP 7, PHP 8)

Oft will man eine Anweisung ausführen, wenn eine bestimmte Bedingung erfüllt ist, und eine andere Anweisung, wenn dies nicht der Fall ist. Dies ist der Einsatzzweck von else. else erweitert eine if-Anweisung um eine weitere Anweisung, die dann ausgeführt werden soll, wenn der Ausdruck in der if-Anweisung zu false ausgewertet wird. Der folgende Programmcode würde z. B. a ist größer als b ausgeben, wenn $a größer als b ist, ansonsten a ist NICHT größer als b

<?php
if ($a > $b) {
echo
"a ist größer als b";
} else {
echo
"a ist NICHT größer als b";
}
?>
Die else-Anweisung wird nur dann ausgeführt, wenn der if-Ausdruck und alle etwaigen elseif als false ausgewertet wurden (siehe auch elseif).

Hinweis: Baumelndes (dangling) else

Bei verschachtelten if-else-Anweisungen wird ein else immer mit dem nächsten if verbunden.

<?php
$a
= false;
$b = true;
if (
$a)
if (
$b)
echo
"b";
else
echo
"c";
?>
Trotz der Einrückung (die bei PHP keine Rolle spielt), ist das else mit dem if ($b) verbunden, weshalb das Beispiel keine Ausgabe erzeugt. Obwohl diese Vorgehensweise zulässig ist, sollte sie durch die Verwendung geschweifter Klammern vermieden werden, um mögliche Mehrdeutigkeiten aufzulösen.

add a note

User Contributed Notes 2 notes

up
20
dormeydo at gmail dot com
15 years ago
An alternative and very useful syntax is the following one:

statement ? execute if true : execute if false

Ths is very usefull for dynamic outout inside strings, for example:

print('$a is ' . ($a > $b ? 'bigger than' : ($a == $b ? 'equal to' : 'smaler than' )) . ' $b');

This will print "$a is smaler than $b" is $b is bigger than $a, "$a is bigger than $b" if $a si bigger and "$a is equal to $b" if they are same.
up
11
Caliban Darklock
19 years ago
If you're coming from another language that does not have the "elseif" construct (e.g. C++), it's important to recognise that "else if" is a nested language construct and "elseif" is a linear language construct; they may be compared in performance to a recursive loop as opposed to an iterative loop.

<?php
$limit
=1000;
for(
$idx=0;$idx<$limit;$idx++)
{
$list[]="if(false) echo \"$idx;\n\"; else"; }
$list[]=" echo \"$idx\n\";";
$space=implode(" ",$list);| // if ... else if ... else
$nospace=implode("",$list); // if ... elseif ... else
$start=array_sum(explode(" ",microtime()));
eval(
$space);
$end=array_sum(explode(" ",microtime()));
echo
$end-$start . " seconds\n";
$start=array_sum(explode(" ",microtime()));
eval(
$nospace);
$end=array_sum(explode(" ",microtime()));
echo
$end-$start . " seconds\n";
?>

This test should show that "elseif" executes in roughly two-thirds the time of "else if". (Increasing $limit will also eventually cause a parser stack overflow error, but the level where this happens is ridiculous in real world terms. Nobody normally nests if() blocks to more than a thousand levels unless they're trying to break things, which is a whole different problem.)

There is still a need for "else if", as you may have additional code to be executed unconditionally at some rung of the ladder; an "else if" construction allows this unconditional code to be elegantly inserted before or after the entire rest of the process. Consider the following elseif() ladder:

<?php
if($a) { conditional1(); }
elseif(
$b) { conditional2(); }
elseif(
$c) { conditional3(); }
elseif(
$d) { conditional4(); }
elseif(
$e) { conditional5(); }
elseif(
$f) { conditional6(); }
elseif(
$g) { conditional7(); }
elseif(
$h) { conditional8(); }
else {
conditional9(); }
?>

To insert unconditional preprocessing code for $e onward, one need only split the "elseif":

<?php
if($a) { conditional1(); }
elseif(
$b) { conditional2(); }
elseif(
$c) { conditional3(); }
elseif(
$d) { conditional4(); }
else {
....
unconditional();
....if(
$e) { conditional5(); }
....elseif(
$f) { conditional6(); }
....elseif(
$g) { conditional7(); }
....elseif(
$h) { conditional8(); }
....else {
conditional9(); }
}
?>

The alternative is to duplicate the unconditional code throughout the construct.
To Top